Securitron PB5 User Manual download pdf

Securitron Magnalock Corp. www.securitron.com ASSA ABLOY, the global leader

Tel 800.624.5625 [email protected]

in door opening solutions

Page 1 Rev. C, 07/11

SECURITRON PB5 EXIT BUTTON

INSTALLATION AND OPERATING INSTRUCTIONS

1. DESCRIPTION

The model PB5 is a spring loaded momentary 2" diameter, illuminated exit button, mounted on a

stainless steel single gang outlet box cover. The DPST contacts switch when the button is

depressed and return when it is released. The contacts are UL listed with 5 AMP capacity. The

PB5 can be used for momentary release of fail safe or fail secure electric locks. It may also be

used to input a REX (request to exit) signal to a card reader system for release of an electric

lock. We recommend that the local building or fire safety authority be consulted prior to using

exit buttons for door egress. They may require a "no special knowledge" exit device such as

Securitron's Touch Sense Bar.

2. INSTALLATION

The PB5 comes with a retro-fit wall mounting device and color coded hookup wires installed. If a

wall box is used, be sure it is at least 2 1/2" deep to accommodate the switch. The drawing

below identifies the unit's connection points.

NOTE PRESENCE OF UN-WIRED

NO1 AND N 2 SPADE TERMINALS

ON CONTACT BLOCKS FOR

SPECIAL USES

WIRE IDENTIFICATION

WHITE/RED

REAR OF UNIT SHOWN

GREEN

BLACK

RED

BLUE

REMOVE OUTER RESISTOR

FOR 12 VDC OPERATION

NOTE: LIGHTS OPERATE

ON 24 VDC IF RESISTORS

ARE NOT REMOVED

GREEN = SWITCH LED POSITIVE

BLACK = COMMON DC NEGATIVE

RED =

BLUE =

SWITCH N.C. 1

SWITCH N.O. 2

WHITE/RED = COMMON 1

WHITE/BLUE = COMMON 2

1.2 K

1/4W

620 OHM

1/4W

COM

N.O.

N.C.

TERMINAL TYPE

.250” QUICK CONNECT

3. LED OPERATION

Resistors are installed so that the LED may be operated on either 12 or 24 VDC. The green wire

that drives the switch LED has resistors soldered on it. If the power supply is 24 VDC, connect

directly to the wire. If the power supply is 12 VDC, remove the outer resistor for proper

operation at the lower voltage.

The switch LED draws 9 mA @ 12VDC or 20 mA @ 24VDC. For replacement: the switch LED is

Securitron part number 030-14600. The switch LED is replaced by grasping the back of the

white contact block and twisting it counter-clockwise to the 11 o’clock position, then pull the

contact block straight out of the rear of the switch. This reveals the LED which then can be

pulled out from the block. Insert new LED into contacts, the

 marking on the LED should be on

the same side as the green wire with printing facing the same directions as the switch block

terminals. Operating Life of the switch LED is 100,000 hours.

For LED replacement in older PB5: The switch LED assembly is replaced by snapping out the

contact block assembly at the rear of the switch. Remove the PCB and replace with LED

following the steps above.

1 2

Summary of Contents

Page 1 - SECURITRON PB5 EXIT BUTTON

Securitron Magnalock Corp. www.securitron.com ASSA ABLOY, the global leader Tel 800.624.5625 [email protected] in door opening solution

Page 2 - Page 2 Rev. C, 05/11

PN# 500-23150 Page 2 Rev. C, 05/11 4. WIRING The drawings below show two common applications. The first shows momentary release of a fail saf

Comments to this Manuals

No comments

Securitron PB5 User Manual

Browse online or download User Manual for For Home Securitron PB5. Securitron PB5 User Manual [de]

Summary of Contents

Comments to this Manuals

Related products and manuals for For Home Securitron PB5