Securitron PB3AN User Manual download pdf

Securitron Magnalock Corp. www.securitron.com ASSA ABLOY, the global leader

Tel 800.624.5625 [email protected]

in door opening solutions

Page 1 Rev. D, 02/12

SECURITRON PB3, PB3A, PB3N, PB3AN EXIT BUTTON

INSTALLATION AND OPERATING INSTRUCTIONS

1. DESCRIPTION

The model PB3 is a spring loaded momentary rectangular exit button, with bi-color illumination,

mounted on a stainless steel single gang outlet box cover. The model PB3A is alternate action

(push-on; push off). Adding "N" to the part #(PB3N, PB3AN) yields mounting on a 1 3/4"

narrow stile plate. The NO and NC (DPST) contacts switch when the button is depressed and

return when it is released. The switch is UL listed with 3 AMP capacity. Note that the switch

type is double pole double throw. Two of the contacts are not factory wired (see drawing

below). The reason for this is that all six contacts are rarely required and providing less factory

wiring makes for a less crowded hookup. The installer may use these contacts by soldering

leads to them.

The red and green lamps can be individually operated according to the needs of the installation.

The red lamp is an LED mounted above the button and the green lamp is an LED, illuminating

the button itself. The PB3 can be used for momentary release of fail safe or fail secure electric

locks. If interfaced with a release hold timer, such as Securitron's TimeMate, it can provide for

timed release of electric locks. It may also be used to input a REX (request to exit) signal to a

card reader system. We recommend that the local building or fire safety authority be consulted

prior to using exit buttons for door egress. They may require a "no special knowledge" exit

device such as Securitron's Touch Sense Bar.

2. INSTALLATION

The PB3 comes with a retrofit backbox and color coded hookup wires installed. The backbox

(Securitron PN# 560-10200) includes a template. The drawing below shows the unit's

connection points.

YELLOW

RED LED

REAR OF UNIT SHOWN

GREEN

REMOVE OUTER

RESISTOR FOR

12 VDC OPERATION

BLACK

YELLOW= RED LED POSITIVE

BLACK= COMMON DC NEGATIVE

WIRE IDENTIFICATION

NOTE: LIGHTS

OPERATE ON

24 VDC IF

RESISTORS NOT

REMOVED

GREEN= GREEN LED POSITIVE

REMOVE RESISTOR

FOR 12 VDC

OPERATION

RED/WHITE (COM 1)

BLUE/WHITE (COM 2)

RED (NC 1)

BLUE (NO 2)

NO1

NC2

NOTE THAT NO1 AND NC2 ARE NOT

FACTORY WIRED BUT MAY BE WIRED

BY THE INSTALLER IF DESIRED

3. LAMP OPERATION

Resistors are installed so that the lamps may be operated on either 12 or 24 VDC. The yellow

wire drives the red LED and the green wire drives the green LED. The yellow wire has a single

resistor soldered in line and the green wire has two resistors soldered in line. If the power

supply is 24 VDC, connect directly to the wires. If the power supply is 12 VDC, remove the

resistor on the yellow wire and the outer resistor on the green wire for proper operation at the

lower voltage.

1 2

Summary of Contents

Page 1 - WIRE IDENTIFICATION

Securitron Magnalock Corp. www.securitron.com ASSA ABLOY, the global leader Tel 800.624.5625 [email protected] in door opening solution

Page 2 - LED Back View

PN# 500-15100 Page 2 Rev. D, 02/12 Flat sectionFlat sectionLED Back ViewThe red indicator draws 20 mA at either voltage. For replacement: the

Related models: PB3N | PB3A | PB3 |

Comments to this Manuals

No comments

Securitron PB3AN User Manual

Browse online or download User Manual for For Home Securitron PB3AN. Securitron PB3AN User Manual

Summary of Contents

Related models: PB3N | PB3A | PB3 |

Comments to this Manuals

Related products and manuals for For Home Securitron PB3AN